Sp-controls PixiePlus Instrukcja Użytkownika

PixiePlus™ Device Control ModuleInstallation Guide(Decora™ wall plate not included)PXE-DCM+PXE-DCM-BLUE+PXE-DCM-AMBER+PXE-DCM-GREEN+Patent US 7,334,06

IV. PixiePlus Installation cont’d4. Wire Additional Assemblies to Control Multiple Display Devices (Optional)To control multiple devices,wire each add

V. Program PixiePlusIR Programming OverviewThe PixiePlus controls AV devices by learning and duplicating the IR codes of theirremote controls. A singl

V. Program PixiePlus cont’d3. Test Remote and Identify Sweet Spot: Position the remote control a few inchesfrom the IR learning eye (upper right of Pi

V. Program PixiePlus cont’d5. To program a button with a single code: While the PixiePlus is in learningmode, press the button to be programmed to arm

V. Program PixiePlus cont’dThe armed key will indicate it is ready to learn the first code by flashing once, paus-ing, flashing once, and so on.Hold t

V. Program PixiePlus cont’dIf the button did not seem to learn correctly, press any other button on the PixiePlus,then press the target button again t

V. Program PixiePlus cont’dExample: You wish to configure the PixiePlus to send a power command to a pro-jector and a separate power command to an amp

VI. Configuring Special Features cont’dUse of the Inactivity Shutdown Timer requires the DISCRETE POWER ON/POWEROFF keypad module. Configuration of th

VI. Configuring Special Features cont’d2. Security KeylockThe Security Keylock locks the PixiePlus during disuse to prevent unauthorizeduse. It disabl

VI. Configuring Special Features cont’dIf more than six keys are entered, the PixiePlus will beep and reset to the previouslyconfigured code.4. After

ContentsImportant Safety InstructionsElectrical WarningI. IntroductionII. Installation OverviewIII. Wiring PixiePlus to Display DeviceIV. PixiePlus In

VII. Cloning cont’dCloning Procedure1. Set the recipient to cloning mode. If the PixiePlus has never been programmed,you may set it to cloning mode by

VII. Cloning cont’dWhen the units are correctly lined up, the donor PixiePlus will automatically entercloning mode. Its Status LED will turn solid red

IX. OperationPowerPower buttons control power on the projector or monitor. The PixiePlus is alwayson, and its LED backlit buttons remain continually i

X. TroubleshootingProgramming ProblemsVerify that the PixiePlus is in learning mode for programming. The Status LED con-tinually blinks red when the P

X. Troubleshooting cont’dThe PixiePlus does not control the projector/monitor.Be sure that the code was programmed correctly – try reprogramming the u

WarrantySP Controls warrants all PixiePlus products and accessories against defects in ma-terials and workmanship for a period of five years from the

Important Safety Instructions1) Read these instructions. 2) Keep these instructions.3) Heed all warnings.4) Follow all instructions.5) Do not use this

I. IntroductionEasy Setup and ConfigurationThe PixiePlus (PXE-DCM+) is a single-gang AV control device. The modular buttoninterface is easily customiz

II. Installation OverviewThe PixiePlus ships with:- 1 PixiePlus Circuit Board- 7 White Plastic Button Inserts- 1 Cable Assembly consisting of:1 Plasti

III. Wiring PixiePlus to Display DeviceInstallationPosition the clamshell cable assembly at thedisplay device you wish to control. Wire thecable assem

IV. PixiePlus InstallationSelect the button insert modules that match the design of your remote control. Forexample, if your remote control has a sing

IV. PixiePlus Installation cont’d2. Attach BezelAfter selecting the appropriate insert modules, place them against the circuit boardand secure them in

IV. PixiePlus Installation cont’d3. Wire ControllerConnect the 3-conductor cable to the captive screw connector on the back of thePixiePlus. Be sure t